专业的煤气发生炉厂家!郑州科能机械制造有限公司欢迎您!

郑州科能机械制造有限公司

郑州科能机械制造有限公司联系方式
新闻资讯

出售96管二手电捕焦油器Sell 96 tubes of used electric tar traps

  1、本公司低价出售二手两段式煤气发生炉、二手回转窑、二手电捕焦油器、二手球磨机、二手脱硫塔、二手脱硝塔,因厂家需要厂地,现紧急处理二手96管、73管,120管电捕焦油器,设备八成新以上,本公司可以提供该设备的拆卸、装车、安装、调试等技术服务。联系电话:86-13676907460

  2、本公司长期从事煤气发生炉、回转窑、球磨机、电捕焦油器的设计、制作、安装、调试等技术服务,技术先进,价格合理,质量优。

  3、 煤气发生炉点火前准备

    1、煤气发生炉各运动部件冷态实验正常:检查各减速机内和其它应润滑部位是否加油;灰盘旋转正常;转动方向是否正确;风机启动、停止正常;转向是否正确;自动上煤系统:料斗加料、上升、落料、下降正常;检查各部位螺栓是否拧紧,系统无泄漏;检查钟罩行程、密封是否合格;检查各阀门开关灵活、无故障。

    2、各仪表显示正常。反映灵敏、准确。

    3、各水封水位正常;水套注满水,水位计显示清晰、进出水时液位显示正常。

    4、蒸汽系统循环正常:自动泄压装置正常无堵塞、蒸汽管路畅通,打开蒸汽放散阀。

    5、铺炉:用粒度为30~70毫米的炉渣铺炉至炉渣高出炉篦100mm左右,并摊平。

    二、点火

    1、点火:加入木柴,木柴量以确保引燃煤层为准。木柴应均匀分布于整个炉膛,点燃木柴并使其全部燃旺,点火时应打开煤气发生炉的放散阀,放下钟罩、并用上料小车顶开上煤仓盖。

    2、待木柴燃旺后,可少量加煤燃烧,启动一次风机,以小量风助燃,如有局部未燃烧时,关小风量或停风,并用探扦适当拨动,使煤气发生炉炉膛均匀着火,如果还不能均匀着火,应重新点燃。停风观察炉膛是否均匀着火,如着火情况良好,点火过程即完成。

    3、逐步加煤待煤层达到一定高度时即可正常产生煤气。

    4、待煤气产生正常后,转入供气程序。

1, our company sell used two sections of gas producer, rotary kiln second-hand, second-hand electric tar precipitator, used the ball mill, used the desulfurization tower, second-hand denitration tower, due to the need of manufacturer factory, emergency processing used 96 pipe, 73, 120 tube electric tar precipitator, more than eighty percent of new equipment, the company can provide the equipment disassembly, loading, installation, debugging and other technical services.Contact number: 86-13676907460

2. The company has long been engaged in the design, manufacture, installation and commissioning of gas generators, rotary kilns, ball mills, electric tar traps and other technical services, with advanced technology, reasonable price and excellent quality.

3. Prepare gas generator before ignition

1. Normal cold test of each moving part of the gas generator: check whether oil is added in each reducer and other parts that should be lubricated;Gray spiral turn normal;Whether the rotation direction is correct;The fan starts and stops normally;Whether the turn is correct;Automatic coal feeding system: normal feeding, rising, falling and falling in the hopper;Check whether the bolts in each part are tightened, no leakage in the system;Check whether the stroke and seal of bell jar are qualified;Check that the valve switch is flexible and trouble-free.

2. All instruments display normally.Sensitive and accurate.

3. The water seal level is normal;The water jacket is filled with water, the water level gauge shows clearly, and the liquid level shows normally when entering and leaving the water.

4, steam system circulation is normal: the automatic pressure relief device is normal without blocking, the steam pipeline is smooth, open the steam release valve.

5, shop furnace: with particle size of 30~70 mm slag shop furnace to the furnace slag high grate about 100mm, and flat.

Second, the ignition

1, ignition: add the firewood, the amount of wood to ensure that the coal seam ignition.The firewood should be evenly distributed in the whole furnace, lighting the firewood and making it all burn up, opening the release valve of the gas generator furnace, lowering the bell jar, and opening the top coal bunker cover with the top of the loading car.

2. When the wood is burning well, a small amount of coal can be added for combustion, and the primary fan can be started with a small amount of air to help the combustion. If there is no local combustion, turn down the air volume or stop the air, and stir with the probe stick to make the gas ignite evenly in the furnace.Stop the wind to observe whether the furnace fire uniformly, if the fire condition is good, the ignition process is completed.

3. Gradually add coal until the coal seam reaches a certain height, gas can be generated normally.

4, after the gas production is normal, into the gas supply program.




上一篇:两段式煤气发生炉干式止逆阀 下一篇:没有了